안녕하세요…

제가 오렌지보드 BLE와 오렌지보드 두개를 사용하는데.

오렌지보드 BLE에 업로드시 에러가 계속납니다.

잘 사용하다 두어달 사용하지 않았었구요.

해결방법 아시는분 도움 좀 부탁 드립니다.

 - 아 래 -

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58

         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM3

         Using Programmer              : arduino

         Overriding Baud Rate          : 115200

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xdc

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xdc

avrdude done.  Thank you.

보드에 업로딩중에 문제 발생. 다음을  참고하세요. http://www.arduino.cc/en/Guide/Troubleshooting#upload

참고로 오렌지보드는 문제없이 업로드 됩니다.(소스는 똑같이 Blink.ino)

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58

         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         Copyright (c) 2007-2009 Joerg Wunsch

        System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM6

         Using Programmer              : arduino

         Overriding Baud Rate          : 115200

        AVR Part                      : ATmega328P

         Chip Erase delay              : 9000 us

         PAGEL                         : PD7

         BS2                           : PC2

         RESET disposition             : dedicated

         RETRY pulse                   : SCK

         serial program mode           : yes

         parallel program mode         : yes

         Timeout                       : 200

         StabDelay                     : 100

         CmdexeDelay                   : 25

         SyncLoops                     : 32

         ByteDelay                     : 0

         PollIndex                     : 3

         PollValue                     : 0x53

         Memory Detail                 :

                                  Block Poll               Page                       Polled

           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack

           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------

           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff

           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff

           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00

           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00

           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : Arduino

         Description     : Arduino

         Hardware Version: 3

         Firmware Version: 4.4

         Vtarget         : 0.3 V

         Varef           : 0.3 V

         Oscillator      : 28.800 kHz

         SCK period      : 3.3 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x1e950f

avrdude: reading input file "C:\Users\Dongwook\AppData\Local\Temp\build85fe9d593c6c3a472b2a54cc5e88b608.tmp/BlinkWithoutDelay.ino.hex"

avrdude: writing flash (1006 bytes):

Writing | ################################################## | 100% 0.38s

avrdude: 1006 bytes of flash written

avrdude: verifying flash memory against C:\Users\Dongwook\AppData\Local\Temp\build85fe9d593c6c3a472b2a54cc5e88b608.tmp/BlinkWithoutDelay.ino.hex:

avrdude: load data flash data from input file C:\Users\Dongwook\AppData\Local\Temp\build85fe9d593c6c3a472b2a54cc5e88b608.tmp/BlinkWithoutDelay.ino.hex:

avrdude: input file C:\Users\Dongwook\AppData\Local\Temp\build85fe9d593c6c3a472b2a54cc5e88b608.tmp/BlinkWithoutDelay.ino.hex contains 1006 bytes

avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.34s

avrdude: verifying ...

avrdude: 1006 bytes of flash verified

avrdude done.  Thank you.